Bosch E07 Code: Flow Sensor Problem Explained

Quick Answer

Bosch E07 means the flow sensor turbine is not spinning - it is jammed with mineral scale, not necessarily broken. Cleaning the stuck turbine resolves E07 without replacing any parts in most cases. Access the sensor near the inlet valve, remove the cap, and manually spin the turbine with a toothpick - it should rotate freely. Soak in vinegar to break up scale.

Bosch E07 means the flow sensor inside the dishwasher is not detecting water moving. Either water is not actually flowing (in which case 5UC or E17 would typically appear first), or the flow sensor turbine is jammed with debris and not spinning even though water is passing through. Cleaning a stuck flow turbine often resolves E07 without replacing any parts. If the turbine is clean and spins freely, the sensor's electrical signal may have failed.

BoschDishwasherSeverity: moderateDifficulty: intermediate78% DIY Success

Time to Fix

30–120 min

Difficulty

intermediate

Parts Cost

$22 – $48

Tools Needed

Multimeter, Torx T20 screwdriver

Wrong code?

Not seeing E07 on your display?

Select what your appliance is actually doing and we'll take you to the right guide.

too much water in tub

E17

no water entering tub

SYMPTOM

no water supply detected

5UC

pressure sensor not reading correctly

E31

water flow sensor fault

MieleF10

What Does the E07 Code Mean?

The Bosch flow sensor is a small turbine device installed in the water supply path. As water flows through, the turbine spins and generates pulses that the control board counts to measure water volume. When the turbine is jammed, no pulses are generated, and the board either interprets this as no water flow (E07) or inaccurate volume counting (which can cause E17 overfill). Cleaning the turbine is often overlooked because most DIY guides only mention replacing sensors.

Most Likely Causes

Based on aggregated repair data, here is the probability breakdown for this error code:

Flow sensor turbine jammed by mineral scale or debris40%

Flow sensor electrical failure24%

Low water pressure causing insufficient turbine rotation22%

Wiring harness damage between sensor and control board14%

Symptoms You May Notice

E07 displayed during fill phase
Dishwasher not filling despite water supply being on
E07 with normal water pressure at the supply tap
E07 alternating with 5UC or E17 codes

Can you reset a Bosch dishwasher to clear the E07 code?

After cleaning the turbine or replacing the sensor, hold Start/Reset for 5 seconds and run a test fill cycle to confirm E07 is cleared.

Tools Required for Diagnosis

MultimeterTorx T20 screwdriverPliers

Diagnostic Checklist

Follow these steps in order. We start with the easiest external fixes before opening up the machine.

Confirm water supply is fully on

Before diagnosing the sensor, open the cabinet under the sink and confirm the hot water supply valve to the dishwasher is fully open. A partially closed valve can cause insufficient flow to spin the turbine even though some water is entering. Even a valve turned only 80% open can drop the flow rate below the threshold needed for turbine rotation. Turn the valve counterclockwise until fully open - it should not move if already fully open. Run a test cycle to see if E07 clears before proceeding to the sensor.

Locate and clean the flow sensor turbine

Test flow sensor electrical output

Inspect the sensor wiring harness

Replacement Parts

If your diagnostic testing proves the component has failed, you will need a replacement. We recommend OEM parts over aftermarket for water-handling components.

Part Name	OEM Number	Estimated Price
Flow Sensor / Water Quantity Counter00611128 · $22–$48	00611128	$22 – $48

Verify part fitment for your Bosch model

Repair vs. Replace Calculator

Appliance Age (Years)7 Yrs

Labor Approach

Our Verdict

REPAIR

Estimated Cost: $35 (Parts) vs $650 (New Machine)

Frequently Asked Questions

Where is the flow sensor on a Bosch dishwasher?

The flow sensor on a Bosch dishwasher is located in the water intake path, typically integrated into or mounted directly adjacent to the inlet valve assembly at the bottom rear of the unit. To access it, you will need to disconnect the water supply hose and remove the lower access panel. The sensor is a small plastic housing with a 3-wire connector and a visible turbine window on the body. On some models it is a separate component from the inlet valve; on others it is built into the valve body.

Can I clean the flow sensor myself?

Yes, and cleaning is often the only fix needed. The turbine inside the flow sensor can become coated in mineral scale from hard water, preventing it from spinning freely. Access the sensor at the inlet valve area, detach it, and soak it in undiluted white vinegar for 30-60 minutes to dissolve mineral deposits. After soaking, spin the turbine manually with a toothpick - it should rotate freely. Rinse thoroughly with clean water before reinstalling. This free fix resolves E07 in a significant number of cases.

I have E07 but my water pressure is normal - what does that mean?

E07 with normal water pressure indicates the turbine is jammed and not spinning even though water is flowing around it. When the turbine is stuck, no pulses are sent to the control board, which then reports no flow detected even though water is present. This is the most common E07 scenario on dishwashers installed in hard-water areas. Cleaning the turbine rather than replacing the entire sensor should be the first step. If cleaning does not restore turbine rotation, the sensor bearing has failed and the assembly needs replacement.

Flow sensor vs inlet valve - which is more likely to fail and cause E07?

The flow sensor turbine jamming is significantly more likely than a complete inlet valve failure in hard-water areas. The inlet valve solenoid failure is more likely to cause E19 (valve actuation fault) or 5UC (no water at all) rather than E07. E07 specifically means water flow is not being detected or measured, which points directly at the flow sensor rather than the valve that opens to allow water in. Always clean the sensor first before considering valve replacement.

How long does flow sensor replacement take?

Replacing the flow sensor on a Bosch dishwasher takes 30-60 minutes for a first-time DIYer. The main time is spent pulling the unit out from the cabinet, disconnecting and reconnecting the water supply hose, and routing the new sensor's wiring correctly. The sensor itself swaps out in about 5 minutes once it is accessible. Budget an additional 15 minutes for running a test cycle and confirming the E07 is cleared before pushing the dishwasher back into the cabinet.

Related Bosch Dishwasher Error Codes

Code: E17Bosch E17 Error: Overfill Protection Activated Code: SYMPTOMBosch Dishwasher Not Filling with Water: Full Walkthrough Code: 5UCBosch 5UC Code: Water Supply Check Required Code: E31Bosch E31 Code: Water Level Sensor Malfunction

Same Fix on Other Brands

Miele dishwasherF10: Miele Dishwasher F10: Water Intake Issue

Same Fix Works on These Brands

Bosch shares the same hardware platform with these brands. The diagnosis and repair steps are identical.

Bosch dishwasherBosch Dishwasher E15: Fix the Anti-Flood Alert Fast Bosch dishwasherBosch Dishwasher Error Codes: Complete List + Fixes Bosch dishwasherHow to Reset a Bosch Dishwasher (Every Method)Bosch dishwasherBosch E24 Error: Drain Problem Solved Step by Step Bosch dishwasherBosch E25 Code: Drain Pump Fix Without a Technician Bosch dishwasherBosch Dishwasher Not Draining: Every Cause Covered

Models Known to Experience E07 Errors

This repair applies to most Bosch dishwashers with this error code. Common model numbers include:

SHPM88Z75N, SHPM88Z55N, SHPK7ZL55N, SHE3AR75UC, SHEM63W55N, SHPM65Z55N, SHE3AR72UC, SHDF78Z55N, SHEM78ZH5N, SHPM98Z75N

Last verified for technical accuracy on March 14, 2026