Results for “dishwasher”
50 matchesRESET — How to Reset a Bosch Dishwasher (Every Method)
n/a (expanded topic)
E09 — Bosch E09: Heating Element Not Working
Heating element or flow-through heater has failed; water not reaching target wash temperature
E17 — Bosch E17 Error: Too Much Water Coming In
Water inlet valve isn't closing fully, water keeps entering past the target fill level, and the pressure switch catches the overfill and fires E17.
H01 — Bosch H01 Code: Water Taking Too Long to Heat
Water temperature did not reach the target within the allotted time; heating timeout
E11 — Bosch E11 Error: Temperature Sensor (NTC) Fault
NTC thermistor reading out of expected range; open circuit or short detected in temperature sensor
GUIDE — Bosch Dishwasher Troubleshooting: 15 Problems, Fixed
Comprehensive symptom-based troubleshooting guide for Bosch dishwasher problems
E92 — Bosch E92 Error: Control Board Communication Fix
Communication failure between the main control board and the user interface board
E92-40 — Bosch E92-40: Board Configuration Mismatch
The main control board's configuration data doesn't match the UI board. Usually happens when a replacement board ships blank, or gets pulled from a different Bosch model and never reprogrammed. The dishwasher powers on, tries to handshake between the two boards, gets nothing back, and throws E92-40.
E92-10 — Bosch E92-10: User Interface Board Not Responding
The main control board is sending communication signals but getting no response from the user interface board specifically. The main PCB, ribbon cable, and UI board form a communication loop, and E92-10 means the loop breaks at the UI board end.
SA NL — Bosch SA NL Code: What Service Appliance No Light Means
The dishwasher's control board switched from normal user mode into a service diagnostic state reserved for technicians. SA NL stands for Service Appliance, No Light. The board won't accept normal cycle commands while it's stuck in this state.
DIAG — How to Enter Bosch Dishwasher Diagnostic Mode
n/a - guide for accessing the hidden diagnostic test program
E01 — Bosch E01 Error: What's Wrong with the Motor Circuit
Wash motor electrical fault or wiring issue detected by the main control board
E02 — Bosch E02 Error: Motor Circuit Electrical Short
Current is flowing where it shouldn't be inside the wash motor circuit. The control board detects this abnormal path and shuts everything down. Could be winding-to-ground, two conductors touching in the harness, or a failed output stage on the board itself.
E20 — Bosch E20 Error: Wash Motor Not Starting Up
Wash motor not reaching expected RPM or not starting at all
E21 — Bosch E21 Code: Wash Motor Running Slow or Stuck
Wash motor running below expected speed, possibly jammed by debris or worn bearings
E23 — Bosch E23 Code: Drain Motor Failing? Here's What to Do
Drain pump motor malfunction, possibly seized or electrically failed
E07 — Bosch E07 Code: Flow Sensor Problem Explained
Water flow sensor turbine not detecting water movement during fill or wash phase
E31 — Bosch E31 Code: Water Level Sensor Malfunction
Pressure switch or water level sensor providing incorrect or no readings to the control board
E61-03 — Bosch E61-03: Door Lock Mechanism Failure
Door lock actuator not engaging or not reporting back to control board after locking
E19 — Bosch E19 Error: Water Fill Valve Malfunction
Fill valve solenoid not operating correctly or diverter valve not responding to control signal
E05 — Bosch E05 Code: Water Fill Taking Too Long
The dishwasher opened the inlet valve and started the fill cycle but couldn't reach the required water level within the programmed time limit. Usually means restricted flow somewhere between the supply valve and the tub, not a complete blockage.
5UC — Bosch 5UC Code: Water Supply Check Required
Water supply insufficient or not detected at inlet valve; no flow reaching the dishwasher
HUB — Miele Dishwasher Error Codes: G Series Models
Reference directory for all Miele dishwasher fault and error codes across G 4000, G 5000, G 6000, and G 7000 series models
F11 — Miele Dishwasher F11 Drain Error: Filter Cleaning Guide
The drain pump ran its full cycle but couldn't confirm the tub was empty. Either something's blocking the drain path, the pump impeller's jammed, or the motor itself has failed.
F70 — Miele Dishwasher F70 Waterproof System Error Fix
The AquaStop float switch in the machine's base pan detected water, triggering the anti-flood system and closing the inlet hose solenoid valve
F14 — Miele Dishwasher F14 Intake Error: Water Not Entering
The water intake system failed to deliver water to the wash cabinet within the expected fill timeout; the inlet valve, AquaStop hose solenoid, or water supply is the source
F78 — Miele Dishwasher F78 Error Code: Circulation Pump Fault
The pump motor's current draw went abnormal, either spiking because something's jamming the impeller, or dropping to nothing because a winding failed. Either way the control board shuts everything down to stop the motor from overheating and burning out for good.
F13 — Miele Dishwasher F13 Error Code: Salt System Fault
The conductivity sensor inside the salt reservoir is reading a brine concentration that's outside normal range. Basically the salt's gone, the cap's leaking diluted brine back in, or the sensor itself is coated with scale and can't read properly.
RESET — How to Reset a Miele Dishwasher and Clear Fault Codes
The reset process cancels the active wash program, triggers an automatic pump-out drain sequence, and unlocks the door. Fault codes stored in the G-series control board's memory clear on their own once the machine completes a full cycle without detecting the same fault condition again.
F24 — Miele Dishwasher F24 Error Code: Heating Fault
Water temp never hit the target during the wash cycle. The machine gives itself a set amount of time to reach temperature, and when it doesn't get there, it throws F24 and quits. Could be the sensor lying about the temp, or the element actually failing to heat the water.
F51 — Miele Dishwasher F51 Error: Circulation Pump Pressure Fault
The control board detected abnormal pressure or flow in the main wash circuit during the active wash phase. Either not enough water got in, something's blocking the impeller, or the pressure sensor that monitors all of this gave a bad reading when it shouldn't have.
HUB — Thermador Dishwasher Error Codes: DWHD and Sapphire Series
Your Thermador's control board detected a sensor reading outside normal parameters. Whether that's a blocked drain, water in the base pan, a heating failure, or a low supply level, the machine locked itself out to protect the motor and your floor. It's not broken, it's telling you something specific.
E15 — Thermador Dishwasher E15: AquaStop Water Protection
Water leaked into the base pan sitting below the dishwasher tub. A polystyrene float in that pan rose with the water level, pushing against a microswitch that triggered the AquaStop lockout. The machine won't run again until that float drops back down and the pan is dry.
E24 — Thermador Dishwasher E24 Error Code: Drain Fault
The control board ran the drain pump for the maximum allowed time and still detected water sitting in the sump. Could be a blockage stopping flow, or an actual pump failure. The board gives up and throws E24 rather than running the pump indefinitely.
E22 — Thermador Dishwasher E22 Error Code: Filter Blocked
The dishwasher's sensors detected restricted water flow through the triple filter assembly. Water can't recirculate to the spray arms properly, so the machine throws E22 and stops rather than run the pump dry or just leave you with filthy dishes.
E25 — Thermador Dishwasher E25 Error Code: Drain Pump Blocked
The drain pump's impeller is physically blocked. Something slipped through the filter system, landed in the pump housing, and locked the spinning blades up. The machine detects that the pump motor is straining or stalled during the drain phase and throws E25 to stop the cycle.
E09 — Thermador Dishwasher E09 Error Code: Heating Fault
The control board ran a heating check and the water temperature didn't rise the way it's supposed to during the wash or dry phase. Either the element can't generate heat anymore, or the NTC sensor is feeding the board bad temperature data and it thinks something's wrong even when it might not be.
RESET — How to Reset a Thermador Dishwasher and Clear Error Codes
When the control board detects a fault or gets confused mid-cycle, it locks up and stops accepting new commands. A reset wipes that locked state from memory and lets the board reboot fresh. Think of it like force-restarting a frozen phone. Basically the same idea.
SA-NL — Thermador Dishwasher SA NL: Salt and Rinse Aid Refill
The machine's sensors have detected that both the water softener salt reservoir (in the tub floor) and the rinse aid dispenser (on the inner door) have dropped below their minimum fill thresholds. Both need to be topped up before the indicators clear.
DIAG-MODE — Whirlpool Dishwasher Diagnostic Mode: How to Enter
It's a hidden self-test sequence built into the control board. When you enter it, the board runs every major component through its paces, fills the tub, fires the heater, spins the wash motor, and drains it out. It also reads back any stored fault codes the machine logged but never bothered to show you during normal operation.
1H — GE Dishwasher 1H Error Code: Temperature Too High
The high-limit thermostat tripped because water temperature inside the tub exceeded the safe maximum threshold
888 — GE Dishwasher 888 Error Code: Control Board Fault Fix
The main control board has detected an internal fault or crashed into an unrecoverable error state. It's basically the processor throwing up its hands and refusing to continue.
ADORA — GE Adora Dishwasher: Models, Features & Common Issues
Overview of the GE Adora dishwasher product line including model numbers, distinguishing features, and most common repair issues
CFE — GE Dishwasher CFE Error Code: Communication Fault Fix
The main control board lost its communication signal with the user interface board in the door. Basically the two computers can't pass data back and forth anymore, so the whole machine locks up and throws CFE to tell you something's wrong with that link.
HUB — GE Dishwasher Error Codes: Complete Guide to Every Code
Hub page covering all GE dishwasher error codes including H2O, FTD, IH, FED, 1H, 888, CFE, PR5, and NE
FED — GE Dishwasher FED Error Code: Failed End of Drain
The drain pump ran its full timed cycle but the water level sensor never sent the 'all clear' signal back to the control board. Could be actual water still in the sump, or more likely the pressure switch just didn't register the drop in pressure when the tub emptied out.
FTD — GE Dishwasher FTD Error Code: Failed to Drain Fix
The control board started the drain cycle, let the pump run its full allotted time, and the water level sensor never confirmed the tub was empty, so it killed the cycle and logged the failure.
H2O — GE Dishwasher H2O Error Code: Water Not Filling Fix
The dishwasher did not detect sufficient water entering the tub within the expected fill time
IH — GE Dishwasher IH Error Code: Inlet Heater Fault Explained
The inlet heater circuit failed to reach or maintain the target temperature during the wash fill phase
LOCK-CONTROLS — GE Dishwasher Lock Controls: Enable and Disable Control Lock
The control lock disables every button on the panel so nothing works until you unlock it. It's a child lock and accidental-press prevention feature built into the software. Nothing's broken, no sensor has failed. The machine's fine, it's just waiting for you to tell it to accept input again.