Frigidaire Range Oven Control Board: Diagnosis & Replacement

Quick Answer

The Frigidaire range oven control board acts as the central brain, regulating heat and timing for your appliance. In my experience, the most common sign of failure is a completely blank display or an oven element that stays on even after the unit is turned off.

Look, a board that's starting to go will usually give you warning signs before it completely dies on you. Ignore them and you're gambling with a runaway oven that won't shut off, which is a legitimate fire risk. I've shown up to jobs where a shorted board cooked an element for six-plus hours straight while the homeowners were at work. A $150 part swap beats an insurance claim every single time.

FrigidaireOvenSeverity: highDifficulty: intermediate92% DIY Success

Time to Fix

20–45 min

Difficulty

intermediate

Parts Cost

$30 – $280

Tools Needed

Phillips #2 screwdriver, 1/4 inch nut driver

What Does the OVEN-CONTROL-BOARD Code Mean?

OK so here's what you need to know upfront: Frigidaire control boards are generally pretty solid, but they hate two things. Power surges. And self-clean cycles. That self-clean thing especially, because it pushes the oven past 900 degrees and the board is sitting right there soaking up that heat cycle after cycle. I replaced three of these last month alone, all on ranges between 8 and 12 years old, all ran self-clean regularly. There's your pattern.

Most Likely Causes

Based on aggregated repair data, here is the probability breakdown for this error code:

Relay failure (mechanical wear)45%

Electrical surge damage30%

Solder joint fatigue from heat cycles15%

Ribbon cable corrosion or loose connection10%

Symptoms You May Notice

The clock display is completely blank or randomly flickers, even though the range is plugged in and the breaker is on.
F1, F10, or F11 error codes keep coming back even after you clear them, sometimes within minutes.
Oven won't heat at all even though you can see the element looks physically intact.
The bake or broil element keeps glowing after you cancel the cycle or set the oven to off. This is the one you don't want to ignore.
Buttons are unresponsive or you have to press them three or four times to get any reaction.

Can you reset a Frigidaire oven to clear the OVEN-CONTROL-BOARD code?

To reset a Frigidaire oven control board, unplug the range completely or flip its dedicated breaker off. Leave it off for at least 5 minutes, 10 is better. When you restore power, the display should come back and prompt you to set the clock. If an error code reappears immediately after power is restored, write it down and run through the diagnostics above. There's no button-press reset sequence for most Frigidaire EOC boards, a full power cycle is the actual reset procedure.

Tools Required for Diagnosis

Phillips #2 screwdriver1/4 inch nut driverNeedle-nose pliersDigital multimeter (set to ohms)Smartphone (for wiring photos before disassembly)Oven thermometer (for final temperature verification)Work gloves (sheet metal edges will cut you)

Diagnostic Checklist

Follow these steps in order. We start with the easiest external fixes before opening up the machine.

ComponentComponent Under Test

Expected Range1030–1130 ohms

ConditionIf Open (OL) or infinite, replace component.

Replacement Parts

If your diagnostic testing proves the component has failed, you will need a replacement. We recommend OEM parts over aftermarket for water-handling components.

Part Name	OEM Number	Estimated Price
Electronic Oven Control Board316455410 · $140–$280	316455410	$140 – $280
Oven Control Overlay (Black)316419141 · $30–$65	316419141	$30 – $65

Frequently Asked Questions

Does the new control board come with the buttons and glass?

No, usually not. The board itself is just the electronic circuit board and the display. The decorative front panel with the buttons printed on it is called the overlay. You can usually peel your old one off and reuse it on the new board. But if it's cracked, faded, or peeling badly, just order a new overlay when you order the board. They're usually under $30 and it makes the whole repair look factory fresh.

My oven is beeping constantly with an F11 code. Is it the board?

Probably, yeah. F11 means a shorted keypad. It can be the touchpad membrane itself or the board. I usually start by unplugging the ribbon cable that connects the touchpad to the board and cleaning both connectors with a dry cloth. Sometimes a corroded connection causes phantom key presses. But if the F11 comes back within a day or two, you're looking at a new board. Nine times out of ten on Frigidaire, persistent F11 means the board's relay or keypad circuit is gone.

Can I use a board from a different Frigidaire model if it looks the same?

Honestly, don't do it. I know they look identical and the part number might even seem close, but Frigidaire programs each board specifically for its model. Temperature calibration offsets, relay timing, the whole thing is baked into the firmware. I've seen this go wrong where the oven runs 50 degrees hot or won't hold temperature at all because someone used a board from a similar but not matching model. Pull the tag out of your bottom storage drawer, get the full model number, and match it exactly. Takes 30 seconds.

Is it worth repairing a 10-year-old Frigidaire range?

Yeah, usually it is. These ranges are tanks. If the porcelain is in decent shape and the elements are working fine, spending $150 to $200 on a board is way smarter than dropping $800 or more on a new range. The new stuff honestly isn't built any better. I've replaced boards on 15-year-old Frigidaires that are still running great today. The only time I'd say skip the repair is if the range has multiple failing components at the same time, because then you're chasing it forever.

How long does it actually take to swap the control board?

For your first time, budget about an hour. Maybe a little more if the range is in a tight spot. The slowest part is usually pulling the range out and getting the back panel off without scratching everything. The actual wire transfer goes fast if you took that photo. I did one last week start to finish in under 40 minutes, and that included wiping down behind the range because honestly it was pretty bad back there. Second time you do this repair on the same model it'll take you 30 minutes flat.

Models Known to Experience OVEN-CONTROL-BOARD Errors

This repair applies to most Frigidaire ovens with this error code. Common model numbers include:

FFEF3054TS, FFEF3054TW, FGEF3036TF, FGEF3059TF, FGIF3061NF, FFGF3054TS, FGEF3032MWA, FFEF3048LS

Written by

Mike Sullivan

Lead Appliance Repair Technician · 20 years experience

Last verified for technical accuracy on March 17, 2026