Maytag E1 F9 Error: Long Drain Time Detected

Quick Answer

Maytag E1 F9 is the same as F21 - the drain exceeded the time limit. Check the drain hose: it must loop up to counter height (high loop) before dropping to the drain. A hose that runs straight down will siphon water back in. Also clean the drain pump filter on the lower-right front.

E1 F9 and F9 E1 are the same error - the order depends on the control board revision. E1 = drain system, F9 = timeout. This is the newer format equivalent of F21 on older Maytag models. Same causes: clogged pump filter, kinked drain hose, or failed pump motor. Standpipe height check is critical and often missed: the drain hose standpipe must be 39-96 inches from floor per Maytag spec. Too high creates a siphon; too low creates a backflow.

MaytagWasherSeverity: moderateDifficulty: intermediate78% DIY Success

Time to Fix

20–60 min

Difficulty

intermediate

Parts Cost

$45 – $95

Tools Needed

Towels, Pliers

Wrong code?

Not seeing E1 F9 on your display?

Select what your appliance is actually doing and we'll take you to the right guide.

same drain issue, older code format

identical on Whirlpool platform

WhirlpoolF9 E1

What Does the E1 F9 Code Mean?

E1 F9 and F9 E1 are the same drain timeout error displayed in different order depending on the control board revision. On the platforms that use this code format, E1 identifies the drain subsystem and F9 specifies the timeout fault. The root causes and repair steps are identical to the older F21 code.

Most Likely Causes

Based on aggregated repair data, here is the probability breakdown for this error code:

Drain hose too low - siphoning back35%

Clogged drain pump filter35%

Blocked standpipe or disposal20%

Failing drain pump motor10%

Symptoms You May Notice

E1 F9 code displayed during or after drain phase
Water takes too long to drain from the drum
Standing water in drum after cycle completes
Washer stops and displays code mid-cycle

Can you reset a Maytag washer to clear the E1 F9 code?

After repairing the drain issue, run a Rinse and Spin cycle to confirm the drain works. E1 F9 will not return if the drain path is clear.

Tools Required for Diagnosis

TowelsPliersMultimeter

Diagnostic Checklist

Follow these steps in order. We start with the easiest external fixes before opening up the machine.

Clean drain pump filter

Access the drain pump filter from the lower front panel. Place towels and a pan. Remove the filter cap slowly to release trapped water. Clean all debris from the filter and housing.

Check standpipe height

Inspect drain hose for kinks

Test drain pump resistance

Check pressure hose for clog

ComponentComponent Under Test

Expected Range5–10 ohms

ConditionIf Open (OL) or infinite, replace component.

Replacement Parts

If your diagnostic testing proves the component has failed, you will need a replacement. We recommend OEM parts over aftermarket for water-handling components.

Part Name	OEM Number	Estimated Price
Drain Pump AssemblyW10130913 · $45–$95	W10130913	$45 – $95

Verify part fitment for your Maytag model

Repair vs. Replace Calculator

Appliance Age (Years)7 Yrs

Labor Approach

Our Verdict

REPAIR

Estimated Cost: $70 (Parts) vs $550 (New Machine)

Frequently Asked Questions

Is E1 F9 the same as F9 E1 on a Maytag washer?

Yes. E1 F9 and F9 E1 are the same error. The display order (which segment shows first) depends on the control board firmware revision. Both mean the same thing: the drain cycle timed out. Diagnose and repair them identically.

How is E1 F9 different from F21?

They are functionally identical errors. F21 appears on older Maytag models (pre-2014 roughly). E1 F9 appears on newer Maytag platforms. The root causes are the same: clogged pump filter, blocked drain hose, failed pump motor, or a plugged pressure hose. The repair process is identical.

Why does my Maytag washer keep getting E1 F9 after I cleaned the filter?

Recurring E1 F9 after filter cleaning is almost always caused by the pressure hose. This small rubber tube connects the outer tub to the pressure switch. When it clogs with detergent residue, the pressure switch reports water still present in the tub even after it has drained, triggering E1 F9 again. Disconnect the tube and blow through it to clear the blockage. Also check that the standpipe height is within the 39-96 inch spec.

Related Maytag Washer Error Codes

Code: F21Maytag Washer F21: Drain Pump Clog or Failure Code: SYMPTOMMaytag Washer Not Draining Code: 5DMaytag Washer 5D Code: Too Many Suds

Same Fix on Other Brands

Whirlpool washerF9 E1: Whirlpool F9 E1: Long Drain Error

Same Fix Works on These Brands

Maytag shares the same hardware platform with these brands. The diagnosis and repair steps are identical.

Maytag washerMaytag Washer 5D Code: Too Many Suds (Fix It Fast)Maytag washerAll Maytag Washer Error Codes: Complete Lookup Guide Maytag washerHow to Reset a Maytag Washer (3 Methods That Work)Maytag washerMaytag Washer Troubleshooting: Fix 12 Common Problems Maytag washerMaytag Washer LOC Code: How to Unlock the Controls Maytag washerMaytag Washer Not Draining? Here's What to Check

Models Known to Experience E1 F9 Errors

This repair applies to most Maytag washers with this error code. Common model numbers include:

MVWC465HW, MVWB765FW, MHW8100DC, MHW5630HW, MHW5500FW, MHW7000XW, MHW6000XW, MHW3505FW

Last verified for technical accuracy on March 14, 2026