Warning: Disconnect power before servicing.
ErrBase

Maytag F0 E7 Error: Load Detected With Door Open

Quick Answer

Maytag F0 E7 means the washer sensed weight or a load in the drum while the door is open. Simply remove everything from the drum, close the door, and restart. If the code appears with an empty drum, the weight sensor or its wiring may have a glitch. Try a full power-off reset (breaker for 5 minutes) first.

F0 E7 is usually a glitch, not a real problem. The control board received a weight/load signal at the same time the door or lid was detected as open - these two conditions should not occur simultaneously. In most cases: close the door or lid firmly and restart. The less common cause is an intermittent door or lid switch giving false open readings while the lid is actually closed. Run a calibration reset if F0 E7 returns after closing.

MaytagWasherSeverity: low92% DIY Success
Time to Fix
5–20 min
Difficulty
beginner
Parts Cost
—
Tools Needed
None
Wrong code?

Not seeing F0 E7 on your display?

Select what your appliance is actually doing and we'll take you to the right guide.

related load detection issue
RL
door lock related
F5 E2
recalibration reset
RESET
identical on Whirlpool platform
WhirlpoolF0 E7

What Does the F0 E7 Code Mean?

F0 E7 occurs when the control board receives a load signal at the same time the door or lid is reported as open. These conditions cannot both be true simultaneously under normal operation, so the code is usually generated by a transient glitch, an intermittent lid switch, or a recalibration needed after moving the washer.

Most Likely Causes

Based on aggregated repair data, here is the probability breakdown for this error code:

Items remaining in drum60%
Control board sensor glitch25%
Weight sensor fault15%

Symptoms You May Notice

  • F0 E7 displayed - load detected with door open
  • Machine will not accept a new cycle
  • Display shows error before any water is added
  • Occurs consistently when trying to start a wash

Can you reset a Maytag washer to clear the F0 E7 code?

Close door firmly and restart. If F0 E7 returns: open lid, run calibration reset (dial 3 right - 1 left - 1 right within 6 seconds), close lid, press Start.

Diagnostic Checklist

Follow these steps in order. We start with the easiest external fixes before opening up the machine.

1

Close Door or Lid Firmly and Retry

Close the door or lid completely and firmly. Ensure nothing is caught in the door seal or lid gap. Press Start to restart the cycle.

2

Check Lid or Door Switch Engagement

3

Run Calibration Reset

4

Check Leveling After Recent Move

Frequently Asked Questions

How do I clear F0 E7 on a Maytag washer?
Close the door or lid firmly and press Start. In most cases F0 E7 clears immediately. If it returns, unplug the washer for 60 seconds to reset the control board, then run a calibration cycle.
Is F0 E7 a serious error?
No. F0 E7 is a low-severity informational code. It indicates a logic conflict (load detected while door open) that is almost always resolved by simply closing the door and restarting. It does not indicate a mechanical failure in most cases.
Why does F0 E7 appear when the door is closed?
If the door is closed but F0 E7 still appears, the door or lid switch is likely giving an intermittent false open signal. The control board sees the load signal but the switch is telling it the door is open. Replace the lid switch or door lock assembly if the error recurs consistently with a closed door.

Related Maytag Washer Error Codes

Code: RLMaytag Washer RL Code: Items Detected During Clean CycleCode: F5 E2Maytag F5 E2 Error: Door Lock Won't EngageCode: RESETHow to Reset a Maytag Washer

Same Fix on Other Brands

Whirlpool washerF0 E7: Whirlpool F0 E7: Load With Open Door

Same Fix Works on These Brands

Maytag shares the same hardware platform with these brands. The diagnosis and repair steps are identical.

Maytag washerMaytag Washer 5D Code: Too Many Suds (Fix It Fast)Maytag washerAll Maytag Washer Error Codes: Complete Lookup GuideMaytag washerHow to Reset a Maytag Washer (3 Methods That Work)Maytag washerMaytag Washer Troubleshooting: Fix 12 Common ProblemsMaytag washerMaytag Washer LOC Code: How to Unlock the ControlsMaytag washerMaytag Washer Not Draining? Here's What to Check

Models Known to Experience F0 E7 Errors

This repair applies to most Maytag washers with this error code. Common model numbers include:

MVWC415EW, MVWC465HW, MVWB835DW, MVWB765FW, MVWX655DW

Last verified for technical accuracy on March 14, 2026