Warning: Disconnect power before servicing.
ErrBase

Kenmore Dryer F01 Error Code: Main Control Board Fault

Quick Answer

F01 on a Kenmore 600 or 700 series dryer means the main control board has failed or detected an internal fault it cannot recover from. Kenmore 600 and 700 series dryers are built on the Whirlpool platform, so this is the same fault as Whirlpool F01 and Maytag F01. A hard reset clears the code in some cases, but if it returns the board typically needs replacement.

F01 on a Kenmore 600 or 700 series dryer means the main control board has failed or detected an internal fault it cannot recover from. Kenmore 600 and 700 series dryers are built on the Whirlpool platform, so this is the same fault as Whirlpool F01 and Maytag F01. A hard reset clears the code in some cases, but if it returns the board typically needs replacement. Kenmore-branded control boards run approximately $80-180. Confirm your model number starts with 110 to ensure this repair guide applies.

KenmoreDryerSeverity: highDifficulty: advanced85% DIY Success
Time to Fix
45–90 min
Difficulty
advanced
Parts Cost
$80 – $180
Tools Needed
Phillips head screwdriver, Putty knife (to release top panel clips on some models)
Wrong code?

Not seeing F01 on your display?

Select what your appliance is actually doing and we'll take you to the right guide.

control board fault
WhirlpoolF01
control board fault
MaytagF01

What Does the F01 Code Mean?

The main control board in your Kenmore dryer has logged a critical fault. Try a hard reset first. If the code returns, the board needs replacement. This applies to 600 and 700 series models only.

Most Likely Causes

Based on aggregated repair data, here is the probability breakdown for this error code:

Control board internal component failure40%
Power surge or voltage spike damaging board circuits24%
Heat or moisture damage to board components over time14%
Age-related relay or capacitor failure on the board12%
Wiring harness connector loose or corroded at board10%

Symptoms You May Notice

  • F01 displayed on control panel
  • Dryer stops mid-cycle without completing
  • Dryer will not start at all
  • Display shows garbled text or partial digit segments
  • Buttons do not respond to input

Can you reset a Kenmore dryer to clear the F01 code?

Unplug the dryer from the wall outlet for a full 60 seconds, then reconnect. If F01 clears but returns within a few cycles, the board has a recurring internal fault and needs replacement. A reset alone does not fix a failed board.

Tools Required for Diagnosis

Phillips head screwdriverPutty knife (to release top panel clips on some models)Needle-nose pliersMultimeter (optional, to check voltage at board)Smartphone camera (photograph wire positions before disconnecting)

Diagnostic Checklist

Follow these steps in order. We start with the easiest external fixes before opening up the machine.

1

Confirm your Kenmore model series first

Confirm your Kenmore model series first. Find the model tag inside the door frame. If it starts with 110, this is a Whirlpool-platform 600/700 series and this guide applies. If it starts with 796, use the LG platform guide.

2

Perform a hard reset

3

Remove the back panel or control console depending on your model

4

Visually inspect the control board for burn marks

5

Replace the control board

Replacement Parts

If your diagnostic testing proves the component has failed, you will need a replacement. We recommend OEM parts over aftermarket for water-handling components.

Part Name
Main Control BoardW10111606 · $80–$180

Repair vs. Replace Calculator

Appliance Age (Years)7 Yrs
Labor Approach
Our Verdict
REPAIR
Estimated Cost: $130 (Parts) vs $650 (New Machine)

Frequently Asked Questions

Is the Kenmore dryer F01 the same as Whirlpool dryer F01?
Yes, for 600 and 700 series Kenmore dryers. These are built on the Whirlpool platform with identical control boards and identical fault codes. The repair steps, part category, and diagnostic procedure are interchangeable between Kenmore 600/700 and Whirlpool WED-series dryers.
Can I use a Whirlpool control board to replace the board in a Kenmore 600 series dryer?
Yes. Kenmore 600 and 700 series dryers use the same Whirlpool-manufactured control board. The Whirlpool OEM part number (such as W10111606) is directly compatible. Cross-reference with your specific Kenmore model number to confirm the correct board revision.
My Kenmore dryer shows F01 after a power outage. Do I need to replace the board?
Not necessarily. First try unplugging the dryer for 60 seconds to clear the fault from memory. Power outages can cause transient faults that trigger F01 without any real board damage. If the code clears and does not return within 5 cycles, the board is likely fine.
How do I know if my Kenmore dryer is the 600/700 series (Whirlpool) or 800 series (LG)?
Check the first three digits of your model number on the door frame label. Model numbers starting with 110 are 600/700 series (Whirlpool platform). Model numbers starting with 796 are 800 series (LG platform). These use different parts and different code systems.
Is board replacement covered under Kenmore warranty?
Kenmore's standard warranty covers parts and labor for 1 year from purchase. After that period, an extended protection plan would cover the board. Out of warranty, the control board runs $80-180 plus labor if using a technician. A surge protector significantly reduces the risk of board failure from voltage spikes.

Related Kenmore Dryer Error Codes

Code: HUBKenmore Dryer Error Codes Guide

Same Fix on Other Brands

Whirlpool dryerF01: Whirlpool Dryer F01 Error CodeMaytag dryerF01: Maytag Dryer F01 Error Code

Models Known to Experience F01 Errors

This repair applies to most Kenmore dryers with this error code. Common model numbers include:

11062132410, 11061102310, 11079422800

Last verified for technical accuracy on March 14, 2026