Warning: Disconnect power before servicing.
ErrBase

Whirlpool Oven E1F6 Error Code: Temperature Sensor Out of Range at Startup

Quick Answer

Whirlpool E1F6 is the same code as F6E1 displayed in reverse order on some models. It means the oven temperature sensor read an abnormal temperature at startup - either much higher or lower than ambient room temperature. If the oven was recently used and is still warm, E1F6 may appear briefly and clear when the sensor reads within normal range.

Whirlpool E1F6 is the same code as F6E1 displayed in reverse order on some models. It means the oven temperature sensor read an abnormal temperature at startup - either much higher or lower than ambient room temperature. If the oven was recently used and is still warm, E1F6 may appear briefly and clear when the sensor reads within normal range. If it appears with a cold oven, the sensor or its wiring has failed.

WhirlpoolOvenSeverity: mediumDifficulty: intermediate75% DIY Success
Time to Fix
20–90 min
Difficulty
intermediate
Parts Cost
$15 – $250
Tools Needed
Multimeter, Nut driver set

What Does the E1 F6 Code Mean?

Whirlpool oven E1 F6: E1F6 on a Whirlpool oven means the temperature sensor reading was out of expected range when the oven first powered on.

Most Likely Causes

Based on aggregated repair data, here is the probability breakdown for this error code:

Heating element grounded40%
Control board fault24%
Keypad membrane short14%
Wiring harness damage12%
Temperature sensor failure10%

Symptoms You May Notice

  • E1 F6 on display
  • Oven stops or behaves abnormally
  • May trip circuit breaker (ground faults)

Can you reset a Whirlpool oven to clear the E1 F6 code?

Turn circuit breaker off for 60 seconds. Turn on. If code returns immediately, the fault is persistent. Some codes clear after the oven cools down from self-clean.

Tools Required for Diagnosis

MultimeterNut driver setFlashlight

Diagnostic Checklist

Follow these steps in order. We start with the easiest external fixes before opening up the machine.

1

Turn breaker off 5 minutes

Turn breaker off 5 minutes. Test if code returns.

2

Based on the code, inspect the related component (element,

3

Replace and test.

Replacement Parts

If your diagnostic testing proves the component has failed, you will need a replacement. We recommend OEM parts over aftermarket for water-handling components.

Part Name
Whirlpool Bake ElementModel-specific · $25–$60
Whirlpool Oven Control BoardModel-specific · $100–$250
Whirlpool RTD Temperature SensorModel-specific · $15–$30

Repair vs. Replace Calculator

Appliance Age (Years)7 Yrs
Labor Approach
Our Verdict
REPAIR
Estimated Cost: $133 (Parts) vs $1900 (New Machine)

Frequently Asked Questions

Is Whirlpool E1 F6 dangerous?
Ground fault codes (F6E4) are a shock hazard - do not use the oven until repaired. Other codes disable the oven but are not an immediate safety risk.
Can I use my oven with this code?
The oven will not operate with an active fault code. Fix the underlying issue to restore operation.
How much does repair cost?
Sensor: $15-30 + labor. Element: $25-60 + labor. Board: $100-250 + labor. Typical total: $150-400.

Related Whirlpool Oven Error Codes

Code: HUBWhirlpool Oven Error Codes

Same Fix Works on These Brands

Whirlpool shares the same hardware platform with these brands. The diagnosis and repair steps are identical.

Maytag washerMaytag Washer 5D Code: Too Many Suds (Fix It Fast)Maytag washerAll Maytag Washer Error Codes: Complete Lookup GuideMaytag washerHow to Reset a Maytag Washer (3 Methods That Work)Maytag washerMaytag Washer Troubleshooting: Fix 12 Common ProblemsMaytag washerMaytag Washer LOC Code: How to Unlock the ControlsMaytag washerMaytag Washer Not Draining? Here's What to Check

Models Known to Experience E1 F6 Errors

This repair applies to most Whirlpool ovens with this error code. Common model numbers include:

WFE515S0ES, WOS72EC0HZ, WOD51EC0HZ, WEE510S0FS

Last verified for technical accuracy on March 15, 2026